VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  THC Vape  /  THC Vape factory check for overseas buyers
THC vape products · private label sellers

THC Vape factory check for overseas buyers

If you are comparing three quotes for THC vape, compare the paperwork first. Test reports, artwork files, batch coding and the replacement clause tell you more about a supplier than the unit price on page one.

Published 26 September 2026  ·  VapeWholesaleHub  ·  Reading time 7 min

Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.
Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Carton-ready units from the same batch, coded for traceability.
Carton-ready units from the same batch, coded for traceability.

Reading a quotation properly

Buyers come to us for THC vape after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for private label sellers.

We publish a realistic band of 3.54 to 9.49 per unit for standard configurations at 240 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

The cheapest way to lower your cost per unit is usually to remove a SKU, not to negotiate a discount. Fewer lines means larger runs, fewer changeovers and a better price at the same quality.

Choosing the core line

Most private label sellers arrive with a spreadsheet and leave with too many SKUs. The fix is not a bigger catalogue, it is a narrower core. We normally propose three tiers: a volume line that carries the shelf, a step-up line that lifts basket value, and one trial SKU that tells you what to order next season.

Sourcing trips still matter for volume buyers. Seeing the line, the ageing room and the packing station tells you in an hour what six emails cannot. We host visits by appointment and we do not stage them.

For private label sellers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Merchandising a small range well

Counter space is finite. Three well-chosen SKUs outsell nine crowded ones, and the empty space signals a curated range rather than a clearance table.

Staff knowledge converts better than any poster. If your team can explain the difference between two coils in one sentence, the step-up SKU sells itself.

  • Private label files archived for future rebrands
  • Standing reorder schedule with a fixed cut-off
  • Artwork proof plus physical dummy for custom packaging
  • Document pack prepared per destination market
  • Cartons drop-tested and pallet-counted for clean freight
  • Specification locked in writing before production starts

Quality control, in plain terms

A 0.5 percent defect rate sounds excellent until it lands on a 600 unit order and you are handling three returns in a week. We quote realistic rates per category and we credit in advance for the known failure modes.

We photograph the packing station during production for volume orders. It is a small thing, but it settles most arguments about what was actually in the carton before it was sealed.

Specification summary

Typical specification for this category
Volume1.0 ml
HardwareCeramic core
ThreadProprietary pod
AirflowAdjustable
WindowFull glass
PackagingBlister
Minimum order100 units per SKU, mixed cartons allowed
Lead time30 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

How long does production take?

Around 30 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What is the minimum order for THC vape?

Standard configurations start at 240 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 600 units because of setup time on the line.

Related reading

Need a quotation on THC vape products?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on THC vape products

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us